| |
|
NTDM
- HS SERIES
|
|
Other Products
|
|
|
pDF Downloads
|
|
 |
|
|
HOT SWAP |
 |
1500 - 6000W
3U hIGH (N+1) REDUNDANT
SINGLE OUTPUT RACK MOUNT
POWER SYSTEM |
The NTDM-HS
Series of Hot Swap Rack Systems
offers (N+1) redundant or high power
paralleled outputs of 2 modules
per enclosure. This series is especially
suitable for critical telecommunication
and wireless systems. Standard voltages
are 12V, 15V, 24V, 28V, 48V, 110V
|
|
 |
|
| 12V |
125 |
NTDM-HS-12-125 |
| 15V |
100 |
NTDM- HS-15-100 |
| 24V |
62 |
NTDM-HS-24-62 |
| 28V |
54 |
NTDM-HS-28-54 |
| 48V |
31 |
NTDM-HS-48-31 |
| 110V |
14 |
NTDM-HS-110-14 |
|
| 12V |
CONSULT
FACTORY |
| 15V |
| 24V |
84 |
NTDM-HS-24-84 |
| 28V |
72 |
NTDM-HS-28-72 |
| 48V |
42 |
NTDM-HS-48-42 |
| 110V |
18 |
NTDM-HS-110-18 |
|
| 12V |
CONSULT
FACTORY |
| 15V |
| 24V |
125 |
NTDM-HS-24-125 |
| 28V |
107 |
NTDM-HS-28-107 |
| 48V |
62 |
NTDM-HS-48-62 |
| 110V |
27 |
NTDM-HS-110-27 |
|
RACK CONFIGURATION
| NTDM HS-28-54-PAR:
2 each 1,500 Watt modules in parallel
providing a total of 3,000 Watts. |
NTDM HS-28-54-ORD: 2 each 1,500
Watt modules both operating, providing
a total of 1,500 Watts. Should 1
unit fail, the other unit assumes
the load. |
|
| PARALLEL OPERATIONS |
| POWER FACTOR CORRECTION |
| REDUNDANT OPERATION |
| RUGGEDIZED/MILITARIZED |
| BATTERY BACK-UP |
| YOUR/AMP METERS |
| 3 PHASE INPUT |
| 400 HZ |
| MS CONNECTIONS |
|
| -PAR |
| -PFC |
| -ORD |
| -MIL |
| -LVBD |
| -MTR |
| -3-PH |
| -4HE |
| -MSC |
|
|
- 3U (5.25")
High, 19" Wide Rack-Mount Enclosure
- MTBF >150,000
Hours
- LED Indicators
(each module):
Output Power (good)
Input Power (good)
- All outputs
tightly regulated
- Equipped
with Isolation diodes for redundancy
/ parallel operation
- Circuit
breaker input
- OV/OL/OT
Protection Main Output
- Floating
connectors for hot-swap insertion
- Remote Sensing
post isolation diodes
-
- ORD: Redundant
Operation
- PAR: Parallel
Operation
- MTR: Volt
/ Amp Meter
- PFC: Power
Factor Correction
- MIL: Militarized
/ Ruggedized to meet MIL-STD-810
- LVBD*: Low
Voltage Battery Disconnect for battery
back-up operation (see below for details)
- 3PH: Three-phase
Input
- MS Connectors
- 4HZ:
400 Hz Operation
*Low
Battery Voltage Disconnect (LVBD): The
LVBD Module adds a new dimension to battery
backup power supplies. The power supply
simultaneously charges the battery and
powers the load. If input power fails,
the battery continues to support the load.
However, when the battery voltage drops
below a predetermined level, the LVBD
module disconnects the battery from the
load, thereby protecting the battery from
the damaging effects of complete discharge. |
|
ELECTRICAL:
AC input voltage: (1500W)
85-132 - 175-265 VAC(2000W-3000W)
220 VAC Single-phase or 115/208 Three-phase
Input Frequency: 47-63
Hz
Efficiency: 80% typical
for Single-Output units, 70% typical for
4 multiple outputs units
Line Regulation: +.3%
Load Regulation: +2%
Ripple & Noise: 1%
peak to peak, not to exceed 200mV
Protections: OV, OL, &
OT
Hold-up time: 20ms minimum
In-Rush Current: 60A Max
1/2 cycle
Operating temperature:
-0°C to +50°C standard, -40°C
to +60°C optional
Storage temperature: -40°C
to +85°C
Cooling: Internal ball
bearing DC fan
Size: 5.25" (H) x
19" (W) x 17.75" (L)
Weight: Modules 15 lbs.
each, Rack 10 lbs. |
|
|
|
